Jump to content
Sign in to follow this  
Zuendholz

Ezdok And The 777 Position Problem

Recommended Posts

Hi. I don't know where to ask it, so I do it here :).

 
I have a strange issue with the 777 and EZCA. When I turn on ground or in the air my camera is also moving (what is ok), but is not moving back to the position I saved. I'm always sitting a bit too right or too left after the turns. I always have to correct this again. This is really annoying.
 
What i have done:
 
After installation of the 777 run the ezca.config
Removed the DHM in the fsx.cfg (set to 0)
 
I can disable the "effects" in EZCA but it doesn't solve the problem.
 
I hope you can help me with this annoying problem.
 
PS: All other planes (737 PMDG, A2A.... ) work fine. 
 
Greetings.

Philipp Schwaegerl
 

Share this post


Link to post
Share on other sites

Philipp,

 

Maybe do a short video of the problem then we could try duplicating/testing ezca camera selection at the same airport e.g.


Best Regards,

Vaughan Martell - PP-ASEL KDTW

Share this post


Link to post
Share on other sites

Ok, here is the video. Please ignore the finger and the shaky cam. I had to do this with my handy. But you will get the problem. The airport is FSIA. 

 

And every time I load a new flight after restarting FSX (same airport), the position in the 777 is different.

 

(Excuse me for the quality, just watch the problem. :))

 

 

ezdokq0avy.png


Philipp Schwaegerl
 

Share this post


Link to post
Share on other sites

Philipp,

 

Ok, I will go test.

BTY, you ran over the baggage truck!


Best Regards,

Vaughan Martell - PP-ASEL KDTW

Share this post


Link to post
Share on other sites

on page 134 of the 777 intro manual they talk about this, basically it's an fsx quirk

 

cheers

-andy crosby

Share this post


Link to post
Share on other sites

Thank you for the video and your support.

 

The 737NGX is working fine (also for me). The 777 is the only aircraft with this problem. 

 

During the turn the camera "stuck" in a random position and I don't know what to do and what's causing it. :/


Philipp Schwaegerl
 

Share this post


Link to post
Share on other sites

Philipp,

 

"The 737NGX is working fine (also for me). The 777 is the only aircraft with this problem."

 

"During the turn the camera "stuck" in a random position and I don't know what to do and what's causing it. :/"

 

Well, I do not think it is a problem with FSX  or EZCA then.


Best Regards,

Vaughan Martell - PP-ASEL KDTW

Share this post


Link to post
Share on other sites

Do you think this is a problem with the 777?


Hm, very strange. 


Ok you are right. I disabled EZdok and the problem still exists.


Philipp Schwaegerl
 

Share this post


Link to post
Share on other sites

Do you think this is a problem with the 777?

Hm, very strange. 

I do not know.

 

I noticed you have EZCA "blue" button ON for 360 ... I did not test that.

That is the only other difference .. other than the PMDG T7 ...


Best Regards,

Vaughan Martell - PP-ASEL KDTW

Share this post


Link to post
Share on other sites

This does not happen in planes I have either but I've seen complaints about this before. It's either PC system or the plane.

Share this post


Link to post
Share on other sites

That is a FSX issue. It also happens in other planes than the PMDG 777 but the effect is smaller and you don't recognize it.

If you are near the equator you will recognize it more than e.g. in ESSA (Stockholm, Sweden).
I know, it's strange, but try it yourself ;)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Tom Allensworth,
    Founder of AVSIM Online


  • Flight Simulation's Premier Resource!

    AVSIM is a free service to the flight simulation community. AVSIM is staffed completely by volunteers and all funds donated to AVSIM go directly back to supporting the community. Your donation here helps to pay our bandwidth costs, emergency funding, and other general costs that crop up from time to time. Thank you for your support!

    Click here for more information and to see all donations year to date.
×
×
  • Create New...