calou952002pm36

here is the log file: Deleted Thank you

Hello, I own the MCP combo VRinsight 1, I have no problem with FSX and P3D but I can't get it to work perfectly with FS 2020. I have installed the last version of FSUIPC and Linda, I sart FS2020, FSUIPC and Linda, I made the recommended changes in the fsuipc.ini file, When I load the plane (with PMDG 737 et Airbus Fenix or default plane, I can change with the rotary knob the heading, speed and altitude for a few second but then it doesn't work. In the console admin, it offers to me to roll back to an earlier version, where can I get it ? Thank you for your help.

In a new test I am not using anything other FS 2020 and MCE, the problem is the same as before with heading. No fluctuation FPS. What MCE mean with " New ATC option" ?

I did a new test with only FS 2020 and MCE, the problem is the test.

I use Fsuipc, and the software Linda with MCP Combo VRinsight, and application Android "Cockpit to sim" and nothing else. I don't use mods.

Thank you for your answers with a little delay. I am always looking for solutions to my problem. When I ask my copilot for my callsign, the answer is "callsign is" without naming it. I did a clean install of MCE but I think I have an installation problem without finding the origin. What is necessary to have as .dll or as system files for FS 2020, I have no problem for P3D V5. Gerald what do you mean "Make use of the restored SHIFT + Z" ? Thank's for your help. Pascal I use Fsuipc, and the software Linda with MCP Combo VRinsight, and application Android "Cockpit to sim" and nothing else. I don't use mods.

Thank you for your answers with a little delay. I am always looking for solutions to my problem. When I ask my copilot for my callsign, the answer is "callsign is" without naming it. I did a clean install of MCE but I think I have an installation problem without finding the origin. What is necessary to have as .dll or as system files for FS 2020, I have no problem for P3D V5. Gerald what do you mean "Make use of the restored SHIFT + Z" ? Thank's for your help. Pascal

Hello, When I ask the copilot to set the heading or altitude, it never display the correct value, the heading selector turn without stopping at the good value and stop at a wrong value. I assume you installed MCE to default C:\Program Files (x86)\Multi Crew Experience\ folder I think I am using the last version of MCE 2.8.9.0. Are there any users who have the same problem. Thanks for your help. Pascal

Thank you Gerald. Language was French, it's good now.

Hello Gerald, Thank you it's ok for the voxkey but ATC interact don't work, manage radio communication is disable. I have installed V2.8.8.0. Pascal

I also have this error message: Failed to locate Voxkey Commands profile, custom commands will be ignored for this session. Thank you

Hello, I use Flight Simulator via the Microsoft app store and with the last version of MCE, the ATC does'nt work well. It does'nt respond or responds late, I think the interact with the sim is not done. Thanks for your help. Pascal

No it's the beginning of the flight, I want to have the takeoff clearance but the control asks me every time, display ground frequency , I can not have take-off clearance , and I have more control for the remainder of the flight. but the control asks me every time display ground frequency , I can not have take-off clearance . and I have no more control for the remainder of the flight

Hello, I use the module PFETOXPLANE I recently bought, but I can't exceed the control tower at holding point, PF3 does not give me other instructions for the end of the flight. I think the problem comes from me... Could you help me please. Thank's. Regards, Pascal

Hello, I use linda with combo 1 and I would configure the buttons of the autopilot function for push and pull. Should I use macros or FSUIPC or is there another solution. I have version 1.13 of Linda and FSX SE. Thank you for your help. Pascal