stepell

Hi you got me thinking, and i figured out, somehow i had a mixup with the overhead panels of the different models now my 700 has an OFF, 800 has an AUTO position as it should be, and it makes sense what FO is doing... Sorry my mistake, cheers

Hi Bryan, Maybe i didn't explain my question clear enough: While doing the Checklist (before Taxi, Landing) he asks for Eng.-Start-Switches. (switch position is AUTO) I say "Continuous", The FO is fine with that (same the other way around when switch is on CONT and I say "Auto") The point is not which is the correct setting, i could choose either setting for TO or Landing, but shouldn't setting and my statement match? But that's not the actual issue: I wanted to know why the FO is selecting CONT in the -700 and AUTO in the -800? is this on purpose? The switch is the same in all Models and I think (from my research) it should be in the same setting on all models (CONT) during TO and Landing I have the following suspicion: 1.) In the -800 the FO - for what ever reason - doesn't actually flip the Eng.-Start -Switches - even though he should/wants to (as its done in the other models) 2.) Since statement and switch position isn't checked for matching during the Checklist dialogue it results in this discrepancy....??!! ...am i right, or is there a deeper purpose behind the different switch positions i don't know about? Cheers

Hello, I noticed that on the -700 the FO is setting the Engine Start Switches to CONTINIOUS for T/O (before Taxi) and for landing (as I think is the correct way to do). On the -800 he is setting the Engine Start Switches to AUTO for T/O and LDG He also doesnt correct me if i read back "Continous" even if Auto is selected Are there different procedures between -700 and 800, or is this a bug? I did some searching and I think it should be on CONT on all models?! Win7-64 pro, FS9.1, Ifly 3.2.something, FS2CrewVoice latest update thanks Stefan

did the install of the update (your link) and the nav-cycle (Navigraph 1609) again, nothing changed. Still get the crash while FO is doing the Decent checklist into EHAM, no other issues with FS2Crew... is there a file i can manually change (without the installer), just to be sure? I assume changing the FS2audio.dll wont help either? thanks Stefan

Hi Bryan! I have the same issue with the Decent-Checklist going into EHAM (negative elevation) as mentioned above. FS crashes while FO is reading the Checklist. In event viewer I can see it’s because of the Fs2audio.dll I already installed the update you mentioned (http://www.fs2crew.com/cart/pages/FS2Crew%3A-iFly-737NG-Edition.html) but nothing changed The FS2Crew interface says its Version 2.2 and I can also see that some files are updated Also tried switching between Headset and other speakers as you suggested above I am using the ifly 737 Voice Version in FS9.1 on a Win 7 64 Prof System Running it for quite some time now, no other issues so far. Everything is switched of, no Antivirus on this Computer Also tried downloading it from another PC, just to be sure Is there any solution in the meantime?? Thanks Cheers Stefan

In the last days i tried everything i could think of, including reinstall. No changes. is there anything besides "nonsense numbers" that could make ALT and HDG values run away? is there a difference in the logic between the Level-D and ifly (because ifly workes fine)? despite reinstall, could there be a wrong entry in the panel.cfg?

I have my own PC for FS and havent been using it for 2,3 month, so nothing changed except the win updates and the recent update for IVAP.

Hi, I checked everything as you suggested, still the same. The bar confirms my numbers and syntax are understood correctly. The values for HDG and ALT are also reasonable. Any ideas?!

Hi Bryan I am using FS2crew voice for some years now and it worked fine, but in the last days something wired happened: When using the “SET HDG XXX”, “SET FL XXX” commands the numbers go on running. In general I know about this issue. it happened from time to time in the past and a solution is also mentioned in the manual (switch “voice” off and on again). But now it happens every time. Switching “Voice” off and on helps at first. The running stoppes, but with the next command it runs away again. Often I have to do it 3, 4 times till it works normally again and the numbers don’t run away anymore... Maybe not important but I recognized one thing: Normally the numbers change slower when reaching the commanded value e.g. hdg 300 current, “SET HDG 160” - first numbers are changing fast till maybe 170 then changing slower for the last few steps till reaching 160 now they still slow down before reaching the selected value, but pick up again and keep on running also only happened with HDG and ALT/FL not with SPD (so far) all other commands work perfectly I’ve tried countless times even with preselected flights and switching the FS2C panel to the right situation. I am also looking at the green bar in case the system understands something wrong or picks up things it shouldn’t. The commands are also correctly spoken. (as confirmed at the green bar). I also did a reinstall of the software incl. SP but nothing changed. (it works fine with the ifly737 voice btw.) Can you please tell me what is the general reason that these numbers sometimes (in my case always) run away. Since you mentioned it in the manual there must be something behind. My specs. Win 7 prof (all updates) FS9.1 LevelD (all updates) FS2Crew voice for LevelD767 incl. SP As mentioned, didn’t have this problems before, don’t have this problem with the ifly737 I have my own system just for FS so nothing changed except the regular Win updates and a recent IVAP update. Thanks for your answers cheers Stefan

there isn’t. well, there are some paints out there, works for me. To be honest, I don’t care if the Cargodoor really opens anyway, thanks for the reply, PMDG777 sounds good, but doesn’t help, still on FS9 ;-)

Hi Bryan! After a longer time away from FS I started again with some flights in the "good old" LDS767. For me FS2Crew Voice is a must have for any add-on btw. I wanted to do a cargo flight but it felt a little strange with all that "seat the cabin please" "cabin is ready to go" etc. Probably I could just skip some of the phrases but I think some are mandatory or will appear anyway. Did you ever consider doing a Cargo Version? I mean “just” changing the specific dialogues or leaving the passenger stuff. This of course is not Aircraft type related. Thanks Greetings from Vienna

Hi,maybe its the same i had, solution in the last post: http://forum.avsim.net/topic/293161-speed-speed/CheersStefan

Hi Bryan,will there be a solution for the flaps/speedbrake issue (when they are running over FSUIPC) in V1.1 or maybe later?thanksStefan

Hi Bryan, did you get some response from the iFly Team?

Hi Bryan,sorry, my last post was not fully correct: I have a "general" assignment for buttons/axis and an assignment for each addon aircraft i use regularly. Deleting the iFly assignments caused FSUIPC to use the general assignments (thats why nothing changed).So indeed, when Flaps are not assigned via FSUIPC at all, everything works fine.Not a solution, because now i only can use one or the other, but at least we know for sure whats causing it...thanks for your efforts, hopefully the iFly developers make a fix. I am sure I am not the only one using a Saitek (or other hardware) throttle/flap lever and FSUIPCCheersStefan